AQZレールタイプ温度送信機
最新の価格を取得するお支払い方法の種類: | T/T,Paypal |
インコタームズ: | FOB,CFR,CIF,EXW |
最小注文数: | 2 Piece/Pieces |
輸送方法: | Ocean,Land,Air,Express |
ポート: | NINGBO,SHANGHAI |
お支払い方法の種類: | T/T,Paypal |
インコタームズ: | FOB,CFR,CIF,EXW |
最小注文数: | 2 Piece/Pieces |
輸送方法: | Ocean,Land,Air,Express |
ポート: | NINGBO,SHANGHAI |
モデル: AQZ
ブランド: CJ
販売単位 | : | Piece/Pieces |
ⅰ。ジェネラルは紹介します
まず、メーターを使用してくれてありがとう、このマニュアルには、PCにメーター、操作、パラメーター設定をインストールするための指示が含まれています。
AQZレールタイプの温度トランスミッターは、光電子分離技術、SMT製造プロセス、国際標準DINレールの設置を使用して、当社が最近開発した新しいタイプのメーターであり、広い電圧、小さなサイズ、長寿命、簡単なインストール、強い干渉、およびその他の利点。計装は、PCメーターに関連して、監視および制御メーターに集中するPCまたはPLC制御部品とのRS-485インターフェースを通じて、RS-485のインターフェースを介して、PCメーターに関連して、2つのグループ、2つのグループの同時信号出力、MODBUS契約を使用した通信、MODBUS契約を使用した通信のためのものです。 PCを介してパラメーターを修正できます。
ⅱ 。技術インデックス
1、入力タイプ:Cu50、PT100、K、E、J
2、出力精度:±0.5%fs
3、出力信号:2つのグループ4 ~20ma(パラメーターを介して調整可能、outl)
4、全体の寸法(mm:106×76×25
5、電源:AC/DC 24~36V
6.作業状況:温度0 ~50℃、湿度﹤85%RHなし。
腐食と強い電磁気症。
ⅲ 。サイズの外観とメーター接続スキーム
ⅳ 。コード設定モード
Series | code | Name | Remark | Setting range | Ex-Factory |
1 | Pb | Sensor erroramendment | The sensor have deviation can use itemto revisal | 0~±20.0 | 0.0 |
2 | FILT | Filt modulus | The first order lag filter coefficient, the value is greater, the performance anti-jamming moment is stronger, but the response time lag. The pressure and flow control of its value should be smaller, temperature and level control should be relatively large | 0~50 | 20 |
3 | OUTH | Allow exportsmax value | Restrain maximum value of adjust output. | outL~2200 | 2000 |
4 | OUTL | Allow exports min value | Restrain minimum value of adjust output | 0~outH | 400 |
5 | LocK | Code lock | 0-all the parameter can be revised1-only the SP can be revised | 0~50 | 0 |
6 |
Sn |
Input type |
‘0’Cu50 –50.0~150.0℃; ‘1’Pt100 –199.9~200.0℃;‘2’Pt100 –199.9~600.0℃; ‘3’K -30.0~1300℃;‘4’E -30.0~700.0℃ ; ‘5’ J -30.0~900.0℃;
‘6’T -199.9~400.0℃; ‘7’ S -30~1600℃; ‘8’ R -30.0~1700.0℃; ‘9’ WR25 -30.0~2300.0℃; ‘10’ N -30.0~1200.0℃; ‘11’ Idiosyncratic type ; ‘12’ 0~5V(0~10mA); ‘13’ 1~5V(4~20mA) |
0~13 |
random |
7 | P-SH | Display the high limit | P-SH decide the display range, the value and unit are decided by factory and client freely. | P-SL~9999 | random |
8 | P-SL | Display the low limit | P-SL decide the display range, the value and unit are decided by factory and client freely. | -1999~P-SH | random |
9 | Addr | Communication addres | The meter’s number in the control system | 0~63 | 0 |
10 | BAud | Communication baud rate | ‘0’1200;‘1’2400; ‘2’4800; ‘3’9600 | 0~3 | 9600 |
メーターがPCをRS-485に接続すると、PCを介してメーターパラメーターを修正できます。パラメーターの注文は、表4-1を参照してください。その通信「0」、「9600」のボーレートのデフォルトアドレス。複数メートルを接続するために、PCソフトウェアアドレスは「0」のために修正され、ボーレートは「9600」に変更され、この時点でメーターを接続すると、メニューアドレスパラメーターは他の数値パラメーター(63以下)に変更されます。編集してから、アドレスを修正する別のメーター。各メーターが唯一のアドレスであり、繰り返すことはできません。接続機器の修正が終了するまで。 ⅴメーター通信とパラメーターの修正
注:メーターがアドレスを修正した場合、メーターで最適にラベル付けされたアドレスの数値が混乱を避けます。 PCソフトウェア使用とは、PCソフトウェアのヘルプ機能を指します。
4~ 20mAまたは0 ~10mA線形性電流入力は、250Ωまたは500Ωの抵抗を1°5Vまたは0の5V電圧信号に変更し、A2、28端子から入力することで達成できます。
ⅵ 。障害分析とクリアランス
安全フェンスは高度な生産プロセスを採用し、工場を離れる前に厳密なテストを受け、メーターの信頼性を改善します。間違った操作またはパラメーターの設定によって引き起こされる通常の障害。それ、そしてエージェントまたは私たちとの接触。シート6-1は、毎日のアプリケーションにおける安全フェンスの通常の障害です:
シート6-1一般的な障害処理
fault symptom | analysis of causes | Disposal measurement |
Abnormal power |
1、Poor contact of power cord
2、Power switch without lose |
Check the power |
PC display do not correlate with the facts.(display‘FF’) |
1、Sensor model mismatch
2、Wrong signal connection |
1、Check sensor model and meter interior input parameter 2、check signal wire
3、Check communication wire |
Abnormal output | 1、Wrong connecting output wire |
1、Check output connection
2、Check parameter OUTH、OUTL |
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.